LooLoo is a touchless toilet spray that eliminates toilet odors by spraying essential oils on the toilet bowl’s water surface.
Parts of the LooLoo
Quick and Easy 4-Step Installation:
For your safety, please keep in mind that when activating the LooLoo, it will spray an essential oil from the nozzle at the end of the arm. Please be sure to activate the LooLoo only after it is attached to the toilet. The LooLoo is activated by both the pressing of the main button as well as sensors that detect heat and movement and will dispense during activation. Do not spray into your eyes, onto skin or clothing.
Remove Battery TabPull out the battery tab that sticks out of the battery compartment door on the back of LooLoo
Insert FragranceInsert the LooLoo fragrance bottle into the opening on the bottom of LooLoo. Be sure to slide the fragrance in with the LooLoo flower logo on both the LooLoo and fragrance bottle facing you. This allows the bottle to “clip” into the bottom.
Fit to ToiletLooLoo comes with its flexible rubber arm in a straight position. To make the LooLoo fit any toilet, simply adjust the flexible arm of the LooLoo to fit the side of your toilet bowl. This is done by firmly placing the LooLoo on the side of the toilet, then bending the flexible arm inwards over the toilet bowl rim to ensure a snug fit. After you have bent the arm, remove the LooLoo from the toilet and bend the arm again all the way until it touches the main body of the LooLoo. Then the LooLoo can securely clamp onto the toilet bowl.
*Make sure the LooLoo is positioned on the side or back of the toilet and that the brand is on the outside of the toilet.
Activate LooLooPress the large button on the face of the LooLoo to activate LooLoo. Typically, you will need to press the button 2-4 times to prime the inner pump, once it sprays a mist of fragrance it is ready for use.
Adding / Remove Fragrance bottles
Adding and removing fragrance is
To remove a fragrance bottle, simply press the release darker gray button at the bottom side of the LooLoo. This button will release the bottle and you can gently pull the bottle out of the LooLoo.
To insert a new bottle, ensure that the LooLoo logo on both the LooLoo and bottle are facing you. Another way to ensure the bottle is entering properly is that the notch on the bottom of the bottle should be facing the side, not the center of the LooLoo. As you slip the bottle into the bottom of the LooLoo, it should easily slide into the LooLoo until an audible “click” is heard. The click means the bottle is securely installed in the LooLoo.
Once you have placed the bottle into the bottom, press the spray button a few times to prime the LooLoo.
Your LooLoo comes with three (3) AA-sized batteries preinstalled. You will know when the LooLoo is running low on battery when the button and in-bowl light begin to flash red.
To replace the battery, pick up the LooLoo, remove the battery compartment cover on the back side of the LooLoo. Pull out and dispose of the three batteries. Keep in mind that you can recycle your AA batteries. Put in a new set of AA batteries, place the LooLoo back on your toilet and continue enjoying your LooLoo.
Cleaning of LooLoo
The LooLoo is made of easy-to clean materials. We suggest that you wipe it down regularly. You can use a gentle household cleaner and paper towel or a disinfectant wipe.
Factory Reset or LooLoo Calibration
The LooLoo has an in-bowl sensor located behind the flower-shaped glass lens on the nozzle end of the arm. This sensor determines if a person is sitting on the toilet and triggers the LooLoo to spray the essential oil fragrance onto the water. Given the disparity between toilet lid heights and distances, It is possible that this sensor may trigger upon closing the toilet lid. Should this occur, we programmed a simple calibration process for the LooLoo sensor that you can perform. Please follow these simple steps to calibrate the LooLoo to your toilet:
- Place the LooLoo on the side of the toilet.
- Press and hold the large center button on the LooLoo.
- While holding down the button, move the switch back and forth between “A” and “M” a total of 4 times. At the conclusion of that process, the button will flash green signaling to you that the LooLoo has been reset.